IP Subnet Calculator
Enter an address in CIDR form, such as 192.168.1.10/24, and get the full subnet breakdown.
What you get
The tool shows the network address, broadcast address, subnet mask, wildcard mask, first and last usable host, total addresses, usable hosts and the IP class.
Reading CIDR
The number after the slash is how many leading bits belong to the network. A /24 leaves 8 bits for hosts, giving 256 addresses and 254 usable hosts, because the network and broadcast addresses are reserved.
How to use it
- Enter an address with a prefix, for example 192.168.1.10/24.
- Press Calculate.
- Read the results.
Example
For 192.168.1.10/24 the tool shows:
Network 192.168.1.0 Broadcast 192.168.1.255 Mask 255.255.255.0 Wildcard 0.0.0.255 Hosts 192.168.1.1 - 192.168.1.254 (254 usable of 256)
Common use cases
- Planning subnets for a VPC, VLAN or home lab.
- Writing firewall and security-group rules.
- Checking whether two addresses are in the same network (calculate each and compare the network addresses).
Worked examples you can check by hand
A /26 is a good test because the block size (64) does not divide evenly into what people expect. Enter 10.0.5.77/26. The mask 255.255.255.192 keeps the first 26 bits, and 77 falls in the block that starts at 64, so the network address is 10.0.5.64, the broadcast address is 10.0.5.127, the usable range is 10.0.5.65 to 10.0.5.126, and the wildcard mask is 0.0.0.63. That is 64 addresses and 62 usable hosts.
Larger blocks work the same way. 172.16.0.0/12 covers 172.16.0.0 to 172.31.255.255, which is the whole RFC 1918 private range that starts with 172, and contains 1,048,576 addresses. A small block such as 203.0.113.9/29 has 8 addresses: network 203.0.113.8, hosts .9 to .14, broadcast 203.0.113.15.
Input: 192.168.10.130/25 Network: 192.168.10.128 Broadcast: 192.168.10.255 Mask: 255.255.255.128 Wildcard: 0.0.0.127 Hosts: 192.168.10.129 - 192.168.10.254 (126 usable)
Edge cases: /31, /32 and /0
The usual rule of subtracting two only applies when a subnet has more than two addresses. This tool follows the point-to-point convention for the smallest blocks: a /31 reports 2 usable hosts (both addresses, as described in RFC 3021 for router links) and a /32 reports 1 usable host, the single address itself. If you have been told that a /31 “has zero hosts”, that is the older classful rule.
At the other end, /0 is accepted and shows all 4,294,967,296 addresses. The input must be written as four dotted decimal octets followed by a slash and a prefix of 0 to 32, so 192.168.1.10 on its own, or a netmask written as 192.168.1.10/255.255.255.0, is rejected with an error message.
Mistakes people make with CIDR
- Typing the network address you want rather than a host inside it. That is fine: the tool masks the host bits for you, so 10.0.5.77/26 and 10.0.5.64/26 give the same subnet.
- Assuming the class letter decides the mask. The class shown is derived from the first octet only, for historical reference. Modern routing uses the prefix length, so a 10.x.x.x address can be a /8, a /16 or a /27.
- Forgetting that cloud providers reserve extra addresses. AWS, for example, keeps the first four and the last address of every subnet, so a /28 gives you 11 usable instances there even though the calculator says 14. Check your provider’s documentation.
- Mixing up wildcard and subnet masks in Cisco-style access lists, where the wildcard 0.0.0.63 is what you write for a /26.
What it does not do
It calculates one subnet at a time for IPv4. It does not split a network into several equal subnets, summarise a list of routes into one supernet, work with IPv6, or check whether two CIDR blocks overlap. For overlap checks, compute the network and broadcast of each block and compare the ranges yourself.
Frequently asked questions
How do I calculate usable hosts?
Total addresses minus two: the network address and the broadcast address. The exceptions are /31 (2 usable, point-to-point) and /32 (1 usable), which this tool reports as such.
What is a wildcard mask?
The inverse of the subnet mask, used by some routers and access lists.
Does it support IPv6?
The calculator is for IPv4 CIDR addresses.
Is my data uploaded?
No. This tool runs entirely in your browser, so what you type or paste is not sent to our servers.
Why does my /31 show 2 usable hosts instead of 0?
Because the calculator treats /31 as a point-to-point link, where both addresses are usable, and /32 as a single host. Only blocks larger than two addresses lose the network and broadcast addresses.
Can I type a netmask instead of a prefix length?
No. The input must be in the form address/prefix, such as 10.0.5.77/26. Convert a mask like 255.255.255.192 to its prefix by counting the one bits, which is 26 here.